Offer Technical Support and Customized Solutions

The company is committed to creating new and improved plastic materials to meet the evolving demands of the market.

Is flame retardant equal to non-flammable?

Is flame retardant equal to non-flammable?

2024-03-06 14:13:20
https://youtube.com/shorts/IPNmjNpehDE?si=iHjw4AIX2uzFn0sy
Introduction:


Is flame retardant equal to non-flammable?

Flame retardant materials can reduce the speed of flame spread in a fire, but it does not mean the material will not burn completely. We usually use the UL94 standard to measure the flame retardancy of materials.  


In the realm of material science, ensuring safety and reliability is paramount, especially when it comes to materials' behavior in the event of a fire. Among the various standards available for evaluating flame retardancy, UL94 stands out as one of the most widely recognized and utilized benchmarks. Developed by Underwriters Laboratories Inc. (UL), a leading authority in safety testing, the UL94 standard provides crucial insights into a material's ability to resist combustion and extinguish flames. This blog aims to delve into the intricacies of UL94 flame retardant testing standards, shedding light on its significance and methodologies.

Types of UL94 Flame Retardant Ratings and Testing Procedures and Criteria: 

UL 94-HB test

HB is the lowest flame retardant rating in the UL 94 standard. The test method is to horizontally clamp one end of the test piece at an angle of 45±2 degrees, take an iron mesh, and horizontally fix it 10±1mm below the test piece. The burner (flame height is about 20mm) is set at an angle of 45 degrees, moved to the other end of the test piece and contacts the sample 6mm, and timing starts after 30±1 seconds. When the test piece burns to the 25mm mark, start another timer. If it burns to the 25 mm mark within 30±1 seconds, start another timer and move the burner away.
flame retardant material_1.webp



UL 94 V test

The UL 94-V test is completely different from the HB test. Compared with the HB test, the material has higher flame retardancy. After igniting the sample at the center below the sample with a burner (flame height is about 20mm) for 10±0.5 seconds, move the burner away from the sample at a speed of 300mm/s, at least 150mm away from the sample, and record the first self-ignition time. After the self-ignition stops, immediately perform the second burning. After burning for 10±0.5 seconds, move the burner away and record the second self-ignition time and the red-hot time after the flame is extinguished.
flame retardant material_2.webp

UL 94-5V test

The UL 94-5V test is stricter than the UL 94-V test, and the test is divided into two stages.
First, the strip-shaped sample is placed vertically for combustion testing, and after passing, a flat plate test is conducted.

Phase 1: Fix the test piece horizontally with fixtures or jigs, and move the burner to an angle of 20±5 degrees with the horizontal. The tip of the inner flame contacts the bottom center point of the sample and burns for 5±0.5 seconds, then move the burner away for 5±0.5 seconds, repeat this action five times, and observe and record whether the test piece has holes or damage after the fifth burning.
 

Phase 2: Keep the burner (flame height is about 125mm) moving to the side of the test piece at an angle of 20±5 degrees, so that the tip of the inner flame (height 40mm±2mm) contacts one side of the bottom end of the sample, burn for 5±0.5 seconds, then move the burner away for 5±0.5 seconds, repeat this action five times, and record the self-ignition time and the red-hot time after the flame is extinguished after the fifth burning. 
flame retardant material_4.gif

UL 94 Flame Retardant Rating Determination Standard

UL 94-HB Burning Judgment Criteria

Judgment conditions Burning Rate Flammability rating
Sample thickness 3-13mm ≤40mm/min HB
Sample thickness <3mm ≤75mm/min HB
The flame goes out before the marking line (25||100mm) =0mm/min HB










UL 94-V Burning Judgment Criteria

Judgment conditions
V-0
V-1
V-2
Time after flame application (s)
≤10
≤30
≤30
Total time of flaming (s) (sum of 10 flaming times)
≤50
≤250
≤250
Time of flaming plus glowing after the 2nd flame application (s)
≤30
≤60
≤60

Droplets ignite cotton wool

no no yes
Burn until fixture (sample completely burned) no no no














UL 94-5V Burning Judgment Criteria 

Judgment conditions 5VA 5VB
Flaming plus glowing time after 5 flame applications for any given sample (s) ≤60 ≤60
Droplets ignite cotton wool no no

Sample holed (<3mm)

no yes







Conclusion:


In conclusion, while flame retardant materials play a crucial role in fire safety, it's essential to understand that they don't render materials completely non-flammable. The UL94 standard provides a comprehensive framework for evaluating flame retardancy, ensuring that materials meet stringent safety criteria. By adhering to these standards, manufacturers can enhance the fire safety of their products, fostering consumer confidence and trust. 
Nous contacter
Name

Name can't be empty

* Email

Email can't be empty

Phone

Phone can't be empty

Company

Company can't be empty

* Message

Message can't be empty

Soumettre